Arduino IDE like serial monitor in the Raspberry Pi shell: Unterschied zwischen den Versionen
DCEM (Diskussion | Beiträge) (→Explenation) |
DCEM (Diskussion | Beiträge) |
||
Zeile 11: | Zeile 11: | ||
Reboot the system. | Reboot the system. | ||
− | Source:[https://github.com/watterott/RPi-ShieldBridge/blob/master/docu/Arduino.md] | + | Source:[https://github.com/watterott/RPi-ShieldBridge/blob/master/docu/Arduino.md github.com/watterott/RPi-ShieldBridge] |
Then I run the serial.sh script (you need all three for this to work) | Then I run the serial.sh script (you need all three for this to work) | ||
Zeile 42: | Zeile 42: | ||
== Explanation== | == Explanation== | ||
<pre>stty -F /dev/ttyAMA0 cs8 115200 ignbrk -brkint -icrnl -imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke noflsh -ixon -crtscts</pre> | <pre>stty -F /dev/ttyAMA0 cs8 115200 ignbrk -brkint -icrnl -imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke noflsh -ixon -crtscts</pre> | ||
− | '''Source:'''[http://playground.arduino.cc/Interfacing/LinuxTTY] | + | '''Source:'''[http://playground.arduino.cc/Interfacing/LinuxTTY playground.arduino.cc/Interfacing/LinuxTTY] |
This one i basicaly copy and pasted it, without understanding it. It gets the serial interface in the right mode to talk to an Arduino (with 115200 baud) | This one i basicaly copy and pasted it, without understanding it. It gets the serial interface in the right mode to talk to an Arduino (with 115200 baud) | ||
Version vom 5. April 2014, 22:14 Uhr
For serial communication with an Arduino I wanted an Arduino IDE like serial monitor in the Raspberry Pi shell. Since I could not a find a terminal that did support “line mode” I found another workaround.
If you want to be able to use the Serial Port of the Raspberry Pi you will have to disable the Linux serial console first.
sudo nano /boot/cmdline.txt
Remove references to console: =ttyAMA0,115200 and kgdboc=ttyAMA0,115200
sudo nano /etc/inittab
Remove or comment the line: T0:23:respawn:/sbin/getty -L ttyAMA0 115200 vt100
Reboot the system.
Source:github.com/watterott/RPi-ShieldBridge
Then I run the serial.sh script (you need all three for this to work)
serial.sh
#!/bin/bash stty -F /dev/ttyAMA0 cs8 115200 ignbrk -brkint -icrnl -imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke noflsh -ixon -crtscts sleep 1 tmux new-session -d './serial-in.sh' tmux split-window -v './serial-out.sh' tmux attach-session -d
serial-out.sh
#!/bin/bash while true do read a echo "$a" > /dev/ttyAMA0 done
serial-in.sh
#!/bin/bash while true do cat -A /dev/ttyAMA0|tr "^M$" " " done
Explanation
stty -F /dev/ttyAMA0 cs8 115200 ignbrk -brkint -icrnl -imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke noflsh -ixon -crtscts
Source:playground.arduino.cc/Interfacing/LinuxTTY This one i basicaly copy and pasted it, without understanding it. It gets the serial interface in the right mode to talk to an Arduino (with 115200 baud)
I use:
cat -A /dev/ttyAMA0
to listen to the serial port. Unfortunately there are some unwanted characters at the end of a line. I’m not sure why, but I just replaced them with a space. (That way they just do not any me anymore)
To get data to the Serial port I use:
echo "$a" > /dev/ttyAMA0
I use tmux split screen to be able to see both at the same time.
All of this is probably not a clean or nice solution, but it does what I wanted it to do.